Shop Bee Folks for your Honey!Shop Bee Folks for your Honey!
Results 1 to 6 of 6

Thread: Can't clear!!!

  1. Default Can't clear!!!

    I have a batch of Mead that I can't seem to clear up. I'm @ .094 & added isinglass, Stirred for several minutes W/drill mixer and even added isinglass a second time W/ no result. Appx 70 degrees constant temp. Any suggestions please? I Have other batches that cleared beautifully under same conditions & I'm stuck!!!!
    Thanks in advance.

  2. #2

    Default Re: Can't clear!!!

    Sparkolloid works well with mead. Give this one a try and it should clear.

    Follow the directions for preparing it, let it sit for a good long time, and you should be rewarded with a clear carboy. If not, come back online, post your recipe and we'll see what we can figure out.

    Dan McFeeley

    "Meon an phobail a thogail trid an chultur"
    (The people's spirit is raised through culture)

  3. #3

    Default Re: Can't clear!!!


    Can you post your exact recipe, including ingredients, procedure, temps, etc.? There may be a clue there that we'll be able to spot regarding this.

    Welcome to the Forums, BTW! Glad to have you!


  4. Default Re: Can't clear!!!Recipe

    hank you both for your quick reply, Here is what I did, I'll try the sparkloid unless you guys see something here that I screwed up.

    11-5 Mixed 15 lbs honey W/ 6 gal water, added Tannin 1.085
    12-9 1.000, Racked & added 1 1/2 oz hungarian oak cubes
    2-5 .094, adjusted acid, to 60%, added metabisulphite per directions & added sorbate per directions. then added first pack of isinglass and stirred the hell out of it (alot of air) foamed over a few times so I figured I stirred the isinglass right out the top and when it did not clear in a week tried 1 more pack of isinglass and there she sits, still cloudy!

    Thanks so much again, I wish I found this forum a long time ago,

  5. #5

    Default Re: Can't clear!!!

    Hopefully it's not part of the problem but:

    Never "stir the hell" out of a fermentable past the Aerobic stage. Oxygen is needed during the growth phase of the yeast, but after that it's bad news (unless you are making sherry). Gentle stirring so no air is introduced is all that is needed.

    It doesn't sound like you did anything bad, but I've never used oak cubes - I believe you are supposed to soak or steam them before use. I'm not sure if not doing that could cause haze. Tannin should have also helped with clearing anything. Sounds like such a simple recipe, I'm surprised it's hazed over at all.

    Sparkalloid: 1 teaspoon per gallon. It should be added to 1 to 2 cup(s) boiling water for 15 minutes (some wine journals say just 3 minutes is needed) before adding. Add it in while still hot, stir in gently. I get the mead moving with a gentle stir, then slowly pour. It may take a few weeks to clear completely. Note there is a second type of Sparkalloid that is cold mixed, but not a lot of places carry it. If you have the cold mix type, make sure you don't boil it.

  6. Default Re: Can't clear!!!

    Sparkeloid worked like a charm, Clear & full of lees, Going to rack soon. Thanks for all your inputs. HOWEVER!!!!!
    I have yet a third carbouy that is stuck @ 1.080 for the past few months, I have not yet gone to the Stablization phase , I was told to wait until It gets to about .095 or so. Any thoughts or advice from the pros?

Similar Threads

  1. Mead won't clear
    By amaine in forum Troubleshooting your Mead
    Replies: 19
    Last Post: 01-09-2016, 01:45 PM
  2. What does clear mead look like?
    By kudapucat in forum Mead NewBees - Post your Questions Here
    Replies: 14
    Last Post: 12-22-2010, 06:22 PM
  3. Clear is desirable?
    By Midnight Sun in forum Mead NewBees - Post your Questions Here
    Replies: 17
    Last Post: 09-02-2010, 05:51 AM
  4. Not clear about when 1st should go to 2nd?
    By keepitlow in forum Mead NewBees - Post your Questions Here
    Replies: 3
    Last Post: 08-13-2010, 02:26 AM
  5. Mead Won't Clear
    By MtnBrewer in forum Troubleshooting your Mead
    Replies: 2
    Last Post: 02-06-2007, 07:54 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts